Availability: | |
---|---|
Quantity: | |
580AB
Abelly
Lenth: 5.8m
Width: 2.2m
Thickness of bottom : 5mm
Thickness of Side: 3mm
Materials: 5083 H111 marine aluminum plate
7 pcs 50x50 T Bars
3 Transom Ribs
6mm ploymer on the bottom
Aluminum anti-skip deck with foams
Aluminum Top Rails
3 bench seats and one driver seat
Max Passenger:8
Multi-Port fuel injection Instant starting
Precise throttle response
Outstanding cruising and top-end performance Increased fuel efficiency
Engine Management System
Specially calibrated for the rugged airboat application Knock sensor adjusts for low octane fuel
Automatic spark control provides peak performance in all operating conditions Monitors the vital signs of the lubrication and cooling systems
Rev limiter prevents engine damage for over revving Fuel Control System
Eliminates vapor lock
Protects EFI system against contaminated fuel Premium, extra large fuel filter/water separator Easy to reach and service
Distributorless Ignition
Coil-near-plug ignition system
No points, rotor,condenser or cap
Platinum-tipped spark plugs Longer maintenance intervals Lubrication System
Full pressure full flow filtering system Positive crankcase ventilation Custom all-weather engine cowling
Owners and parts manuals by Pleasurecraft, the airboat industries largest engine and parts supplier
Single serpentine belt
Multi-coat non-corrosive paint
U.S. Coast Guard approved flame arrester Warranty- 1 yr warranty
Electrical System -Enhanced wire harness to meet rigorous Airboat demands Electronic Ignition
12 volt negative ground system High output 100-AMP alternator
Overload damage protection by a manual reset circuit breaker Pre-wired wiring harness with 10 prong disconnect
High-torque positive engagement bottom mount marine starter Temperature,oil pressure and voltage
ENGINE REDUCTION UNIT
Century belt reduction unit 2.3 to 1 Ratio PROPELLER
5- Blade 79" adjustable pitch composite propeller
ENGINE STAND
Automotive Built of 1 " stainless steel tubing (16 gauge)
6- mounting points for automotive (Moog Mounts Rear) (Prothane Mounts-Front) All mounts to be shock mounted to prevent vibration
Mounting bracket to be incorporated into the engine stand for the 40 gallon fuel tank Dual battery rack to be built in the engine frame
Lenth: 5.8m
Width: 2.2m
Thickness of bottom : 5mm
Thickness of Side: 3mm
Materials: 5083 H111 marine aluminum plate
7 pcs 50x50 T Bars
3 Transom Ribs
6mm ploymer on the bottom
Aluminum anti-skip deck with foams
Aluminum Top Rails
3 bench seats and one driver seat
Max Passenger:8
Multi-Port fuel injection Instant starting
Precise throttle response
Outstanding cruising and top-end performance Increased fuel efficiency
Engine Management System
Specially calibrated for the rugged airboat application Knock sensor adjusts for low octane fuel
Automatic spark control provides peak performance in all operating conditions Monitors the vital signs of the lubrication and cooling systems
Rev limiter prevents engine damage for over revving Fuel Control System
Eliminates vapor lock
Protects EFI system against contaminated fuel Premium, extra large fuel filter/water separator Easy to reach and service
Distributorless Ignition
Coil-near-plug ignition system
No points, rotor,condenser or cap
Platinum-tipped spark plugs Longer maintenance intervals Lubrication System
Full pressure full flow filtering system Positive crankcase ventilation Custom all-weather engine cowling
Owners and parts manuals by Pleasurecraft, the airboat industries largest engine and parts supplier
Single serpentine belt
Multi-coat non-corrosive paint
U.S. Coast Guard approved flame arrester Warranty- 1 yr warranty
Electrical System -Enhanced wire harness to meet rigorous Airboat demands Electronic Ignition
12 volt negative ground system High output 100-AMP alternator
Overload damage protection by a manual reset circuit breaker Pre-wired wiring harness with 10 prong disconnect
High-torque positive engagement bottom mount marine starter Temperature,oil pressure and voltage
ENGINE REDUCTION UNIT
Century belt reduction unit 2.3 to 1 Ratio PROPELLER
5- Blade 79" adjustable pitch composite propeller
ENGINE STAND
Automotive Built of 1 " stainless steel tubing (16 gauge)
6- mounting points for automotive (Moog Mounts Rear) (Prothane Mounts-Front) All mounts to be shock mounted to prevent vibration
Mounting bracket to be incorporated into the engine stand for the 40 gallon fuel tank Dual battery rack to be built in the engine frame